Guide · Robot electronics

Powering an SO-101 robot arm: supply, current and safety

The SO-101 is the open-source arm from TheRobotStudio and Hugging Face's LeRobot project. Its six joints are Feetech STS3215 serial servos, and most build problems that are not mechanical come from power: the wrong supply voltage, a supply that is too small, or nothing to cut power when something goes wrong. This page works out the numbers from the servo datasheet and checks them in a simulator you can open and change.

An independent guide, not official LeRobot documentation. Check the servos and supply in your own kit: SO-101 kits are sold in more than one version.

The one rule: match the supply to the servos

  • 7.4 V servos (C001, C044, C046; the leader arm always uses these): a 5 V supply, as in the official parts list.
  • 12 V servos (the optional stronger follower): a 12 V supply of 5 A or more, as the parts list says.
  • Never feed 7.4 V servos from a 12 V supply. Their working range is 4 V to 7.4 V.

Sources: SO-ARM100 / SO-101 bill of materials (TheRobotStudio, Apache-2.0); Feetech STS3215 product specification, edition A/0 (2020-04-10), machine-translated copy.

What one servo draws

From the Feetech STS3215 (7.4 V) datasheet:

ItemAt 6 VAt 7.4 V
No-load current130 mA150 mA
Rated current (at rated torque)500 mA650 mA
Stall current (shaft blocked)2 A2.5 A
Idle current (stopped)6 mA6 mA
Stall torque16.5 kg·cm19.5 kg·cm

A servo only draws its stall current when its shaft is blocked: a joint pushing against the table, a gripper squeezing something hard, or an arm holding a heavy load still.

How much current the whole arm needs

The circuit below is the follower arm's power path: a 5 V supply, about 0.1 Ω of lead and connector, an emergency-stop switch, an ammeter, and six servos. Each servo moving at its rated load is drawn as a 10 Ω load (about 0.5 A at 5 V). The extra branch on the right is one joint stalled (about 1.7 A at 5 V, from 2 A at 6 V). Click its switch to stall that joint, or open the emergency stop.

Open it in the playground to change it and share your version →

CaseSupply currentVoltage at the servos
All six joints moving under load2.83 A4.72 V
The same, with one joint stalled4.27 A4.57 V

So choose a 5 V supply rated for 5 A or more. One stalled joint already takes the arm past 4 A. A smaller supply sags or shuts down mid-move, and the servos lose torque. Notice the voltage at the servos drops too, because of the lead: keep the supply lead short and thick.

This is a simple model: real servos draw changing currents as they accelerate. It is meant for sizing the supply, not for predicting each motor exactly.

Protection: a fuse and an emergency stop

Neither is in the official parts list, but both are cheap and worth adding once the arm moves under its own control:

  • A fuse in the positive lead, a little above the supply rating (for example 6.3 A slow-blow with a 5 A supply). It opens only on a fault such as a short in the servo cable.
  • An emergency stop that cuts the servo supply. When power goes, the servos go limp and the arm falls under its own weight, so let it come to rest on something soft, and keep hands clear of the gripper.
  • Polarity: check the polarity marked on your supply and on the servo board before plugging in.

Parts

PartHow manyLink
Feetech STS3215 servo, 7.4 V (C001, 1/345)
The SO-101 leader also uses 2 × C044 (1/191) and 3 × C046 (1/147).
6 per follower armFind it →
5 V DC power supply, 5 A or more
One stalled joint already pulls about 4.3 A. The supply in the SO-101 parts list has a 5.5 × 2.1 mm barrel plug.
1 per armFind it →
Inline fuse holder and 6.3 A slow-blow fuse
Our suggestion, not part of the official kit: just above the supply rating, so it only opens on a fault.
1 per armFind it →
Latching emergency-stop button
Our suggestion. Rated for at least the supply current.
1 per armFind it →

Supplier links may earn breadboardhub a commission. The full arm parts list (printed parts, servo board, cables) is in the official bill of materials.

Building the 12 V version, or something else?

Ask the AI to adapt the circuit to your servos and supply, and it will simulate the result. Or ask Claude with the breadboardhub connector.

Design the 12 V version with AIUse it in Claude

Sources